Open the PLC software, click on the online-click to read, select FXCPU, the communication COM settings are the same, the transmission speed PLC is set to 9.6, the read PLC switch is placed in the running state, and the write PLC switch is placed in the stop state.
What is the role of the 25-pin connector in the Mitsubishi SC-09 data line?
SC-09‘s multi-function data download line, 25-pin is the head-to-head method, and 25 is the connector for the 8-pin download port.
25-thread cable, available for connection to Mitsubishi A series PLC
Round 8-pin connector can be used to connect the plc of the Mitsubishi fx series
How many pin data lines are used in the Mitsubishi plc fx series jacks?
8-pin round S-terminal, but only 4 pins are actually used inside.
How to realize the communication connection between Mitsubishi FX1S series PLC and computer?
The USB-SC09 is a programming cable for Mitsubishi PLC. The driver for the programming cable must be set up before use.
After the installation driver is finished, make a simple setup.
The setting method is reproduced below. Right click (My Computer) and click Properties. The (System Properties) dialog box is shown, select the hardware, and click (Device Management).
Select (port), find the USB port you installed, right click to display (property) click, display the property dialog bar, select (port setting) to set the COM port of the advanced setting in this dialog box to be in the PLC programming software. The settings are the same ones.
What cable can the Mitsubishi FX-2n series PLC use to connect to the computer?
Mitsubishi plc programming cable, generally use usb-sc09
Mitsubishi PLC and computer USB connection can not communicate ES:01802007
1, the corresponding USB driver is not installed.
2; the reason for the line.
3; communication port selection settings.
To use a line with two integrated blocks, there is a crystal inside, otherwise it cannot communicate with the PLC.
What is the programming cable model of Mitsubishi FX series PLC?
The programming cable type of the FX series PLC is SC-09 cable or USB-SC09-FX cable.
SC-09 is used to connect to the computer serial port. USB-SC09-FX is connected to the computer USB port
Mitsubishi version 8.86 is installed in 90% and cannot be applied on 64-bit platforms.
My Mitsubishi 8.86 version is installed in 90%. It can’t be fitted to a 64-bit platform. Installation can be expected to be completed, that is, the USB communication cable driver cannot be installed.
90% happen to be a USB driver installation.
“Cannot run an x86 build of this utility on x64 platform ”
Click to confirm that internalizing driver failed —-C.windows\temp\wdreg.exe.Error,”
The installation is properly the driver installation fails when the USB communication cable (USB-SC09+) is installed.
My computer WIN7 64-bit original home version with everyone said the method of upgrading to the flagship version of the installation results
I installed a low version of GX Developer 8.52 Mitsubishi Chinese also appeared this symptom, my system win 7 64-bit ordinary home version upgrade flagship version; I found online 8.9.1 can support win 7
I am using the Mitsubishi Q series PLC. Is there any special model for the USB programming data cable?
Model QC30R2
Shielded with magnetic ring
The reliability of transmitting data is better
Mitsubishi plc programming software v8.86 what programming cable
Mitsubishi plc programming software uses the SC09 serial cable or the USB-SC09 cable.
How to set up the communication port of Mitsubishi PLC programming software? I just set up the COM number. I just bought a Mitsubishi PLC program download line USB interface.
You should check the port number of your USB programming cable that is visualized in the port of the hardware manager, such as COM8, then set it to COM8 in the programming software.
In general, COM4 or above will be visualized on the notebook, and COM6 or above will be visualized on the desktop.
Why does Mitsubishi fx not use rs422 instead of rs232
The programming port of the FX1S (8-pin round port) is RS422 serial communication.
Use of usb-sc09-fx communication cable and click “RS-232”.
The COM port should choose the COM port that the communication cable actually occupies.
RS232, RS422, RS485 are distinct serial communication formats.
The computer is RS232 (DB9 pin) communication, the general notebook uses USB,
PLC Cable 